Photonics — Open Access Journal

Real-time observation of ultrafast dynamics in the microcosm is a fundamental approach for understanding the internal evolution of physical, chemical and biological systems. Tools for tracing such dynamics are flashes of light with duration comparable to or shorter than the characteristic evolution times of the system under investigation. While femtosecond (fs) pulses are successfully used to investigate vibrational dynamics in molecular systems, real time observation of electron motion in all states of matter requires temporal resolution in the attosecond (1 attosecond (asec) = 10⁻¹⁸ s) time scale. During the last decades, continuous efforts in ultra-short pulse engineering led to the development of table-top sources which can produce asec pulses. These pulses have been synthesized by using broadband coherent radiation in the extreme ultraviolet (XUV) spectral region generated by the interaction of matter with intense fs pulses. Here, we will review asec pulses generated by the interaction of gas phase media and solid surfaces with intense fs IR laser fields. After a brief overview of the fundamental process underlying the XUV emission form these media, we will review the current technology, specifications and the ongoing developments of such asec sources. Full article

The creation of high energy density plasma states produced during laser–solid interaction on a sub-picosecond timescale opens a way to create astrophysical plasmas in the lab to investigate their properties, such as the frequency-dependent refractive index. Available probes to measure absorption and phase-changes given by the complex refractive index of the plasma state are extreme-UV (EUV) and soft X-ray (XUV) ultra-short pulses from high harmonic generation (HHG). For demanding imaging applications such as single-shot measurements of solid density plasmas, the HHG probe has to be optimized in photon number and characterized in intensity and wavefront stability from shot-to-shot. In an experiment, a coherent EUV source based on HHG driven by a compact diode-pumped laser is optimized in photons per pulse for argon and xenon, and the shot-to-shot intensity stability and wavefront changes are characterized. The experimental results are compared to an analytical model estimating the HHG yield, showing good agreement. The obtained values are compared to available data for solid density plasmas to confirm the feasibility of HHG as a probe. Full article

This paper presents a new analysis of optical sensors based on surface plasmon resonance (SPR) phenomenon and nematic liquid crystal (LC) sensitive layer in the partially ordered state. In particular, the paper studies the influence of degradation in the LC ordering state on the behavior of the plasmon resonance parameters. The degradation in the LC ordering is represented by the order parameter. The explicit treatment of the order parameter is critical when trying to differentiate between a change in alignment and a degradation of alignment in LC in response to the presence of an external stimulus in LC based sensors. When a reduction in ordering occurs, ignoring the order parameter can produce misleading results. This sensor has potential applications in chemical and biological systems. The paper presents a tracking method for the state of alignment and degree of ordering of the partially ordered LC film. This can be achieved via the SPR propagation constant and the critical angle at the interface between a metal and an LC film. Full article

Time resolved extreme ultraviolet (EUV) transient reflectivity measurements on non-equilibrium amorphous carbon (a-C) have been carried out by combining optical and free electron laser (FEL) sources. The EUV probing was specifically sensitive to lattice dynamics, since the EUV reflectivity is essentially unaffected by the photo-excited surface plasma. Data have been interpreted in terms of the dynamics of an expanding surface, i.e., a density gradient rapidly forming along the normal surface. This allowed us to determine the characteristic time ($\tau \lesssim$ 1 ps) for hydrodynamic expansion in photo-excited a-C. This finding suggests an extremely narrow time window during which the system can be assumed to be in the isochoric regime, a situation that may complicate the study of photo-induced metastable phases of carbon. Data also showed a weak dependence on the probing EUV wavelength, which was used to estimate the electronic temperature ($T_e\approx$ 0.8 eV) of the excited sample. This experimental finding compares fairly well with the results of calculations, while a comparison of our data and calculations with previous transient optical reflectivity measurements highlights the complementarities between optical and EUV probing. Full article

Elastic optical networks (EONs) based on orthogonal frequency-division multiplexing (OFDM) are considered a promising solution for the next optical network’s generation. These networks make it possible to choose an adequate portion of the available spectrum to satisfy the requested capacity. In this paper, we consider the impact of spectrum fragmentation along the optical single/multipath routing transmission on the efficiency of the EONs. This involves reducing the fragmentation effects by dynamically updating and controlling the minimum bandwidth allocation granularity (ɡ). We adopt linear and nonlinear dynamic mechanisms, which are denoted as LDAɡ and NLDAɡ, respectively, to choose proper bandwidth granularities that are proportional to the optical link/path bandwidth fragmentation status. In order to avoid either splitting the capacity request over many routing paths, which would increase the management complexity, or encouraging single path transmission, the proposed schemes aim to choose a proper bandwidth allocation granularity (ɡ) for a predefined set of suggested values. Simulation results show that varying the bandwidth granularity based on the optical path fragmentation status can offer an improved performance over fixed granularity with respect to the bandwidth blocking probability, the number of path splitting actions, the throughput, and the differential delay constraint issue in terms of: the network bandwidth utilization and multipath distribution. Full article

It was shown recently that the Fe magnetization reversal in the Fe/MnAs/GaAs(001) epitaxial system, attained by temperature control of the regular stripe pattern of the MnAs α- and β-phases, can also be driven by an ultrashort optical laser pulse. In the present time-resolved scattering experiment, we address the dynamics of the MnAs α-β self-organized stripe pattern induced by a 100 fs optical laser pulse, using as a probe the XUV radiation from the FERMI free-electron laser. We observe a loss in the diffraction intensity from the ordered α-β stripes that occurs at two characteristic timescales in the range of ~10⁻¹² and ~10⁻¹⁰ s. We associate the first intensity drop with ultrafast electron-lattice energy exchange processes within the laser-MnAs interaction volume and the second with thermal diffusion towards the MnAs/GaAs interface. With the support of model calculations, the observed dynamics are interpreted in terms of the formation of a laterally homogeneous MnAs overlayer, the thickness of which evolves in time, correlating the MnAs microstructure dynamics with the Fe magnetization response. Full article

The Liquid-Crystal on Silicon (LCoS) spatial light modulator (SLM) has been used in wavelength selective switch (WSS) systems since the 1990s. However, most of the LCoS devices used for WSS systems have a pixel size larger than 6 µm. Although there are some negative physical effects related to smaller pixel sizes, the benefits of more available ports, larger spatial bandwidth, improved resolution, and the compactness of the whole system make the latest generation LCoS microdisplays highly appealing as the core component in WSS systems. In this review work, three specifications of the WSS system including response time, crosstalk and insertion loss, and optimization directions are discussed. With respect to response time, the achievements of liquid crystal material are briefly surveyed. For the study of crosstalk and insertion loss, related physical effects and their relation to the crosstalk or insertion loss are discussed in detail, preliminary experimental study for these physical effects based on a small pixel LCoS SLM device (GAEA device, provided by Holoeye, 3.74 µm pixel pitch, 10 megapixel resolution, telecom) is first performed, which helps with predicting and optimizing the performance of a WSS system with a small pixel size SLM. In the last part, the trend of LCoS devices for future WSS modules is discussed based on the performance of the GAEA device. Tradeoffs between multiple factors are illustrated. In this work, we present the first study, to our knowledge, of the possible application of a small pixel sized SLM as a switching component in a WSS system. Full article

Studying ultrafast processes on the nanoscale with element specificity requires a powerful femtosecond source of tunable extreme-ultraviolet (XUV) or x-ray radiation, such as a free-electron laser (FEL). Current efforts in FEL development are aimed at improving the wavelength tunability and multicolor operation, which will potentially lead to the development of new characterization techniques offering a higher chemical sensitivity and improved spatial resolution. One of the most promising approaches is the echo-enabled harmonic generation (EEHG), where two external seed lasers are used to precisely control the spectro-temporal properties of the FEL pulse. Here, we study the expected performance of EEHG at the FERMI FEL, using numerical simulations. We show that, by employing the existing FERMI layout with minor modifications, the EEHG scheme will be able to produce gigawatt peak-power pulses at wavelengths as short as 5 nm. We discuss some possible detrimental effects that may affect the performance of EEHG and compare the results to the existing double-stage FEL cascade, currently in operation at FERMI. Finally, our simulations show that, after substantial machine upgrades, EEHG has the potential to deliver coherent multicolor pulses reaching wavelengths as short as 3 nm, enabling x-ray pump–x-ray probe experiments in the water window. Full article

In this paper, we numerically demonstrate a two-layer circular lattice photonic crystal fiber (PCF) biosensor based on the principle of surface plasmon resonance (SPR). The finite element method (FEM) with circular perfectly matched layer (PML) boundary condition is applied to evaluate the performance of the proposed sensor. A thin gold layer is deposited outside the PCF structure, which acts as the plasmonic material for this design. The sensing layer (analyte) is implemented in the outermost layer, which permits easy and more practical fabrication process compared to analyte is put inside the air holes. It is demonstrated that, at gold layer thickness of 40 nm, the proposed sensor shows maximum sensitivity of 2200 nm/RIU using the wavelength interrogation method in the sensing range between 1.33–1.36. Besides, using an amplitude interrogation method, a maximum sensitivity of 266 RIU⁻¹ and a maximum sensor resolution of 3.75 × 10⁻⁵ RIU are obtained. We also discuss how phase matching points are varied with different fiber parameters. Owing to high sensitivity and simple design, the proposed sensor may find important applications in biochemical and biological analyte detection. Full article

The transmission impairments of a Raman amplified link using dual-polarization 16-quadrature amplitude modulation (DP-16QAM) are experimentally characterized. The impact of amplitude and phase noise on the signal due to relative intensity noise (RIN) transfer from the pump are compared for two pumping configurations: first-order backward pumping and bi-directional pumping. Experimental results indicate that with increased Raman backward pump power, though the optical signal-to-noise ratio (OSNR) is increased, so is the pump-induced amplitude and phase noise. The transmission performance is firstly improved by the enhanced OSNR at a low pump power until an optimum point is reached, and then the impairments due to pump-induced noise start to dominate. However, the introduction of a low pump power in the forward direction can further improve the system’s performance. Full article

We employ an extreme ultraviolet (XUV) pulse to impulsively excite dipole polarization in atoms or molecules, which corresponds to coherently prepared superposition of excited states. A delayed near infrared (NIR) pulse then perturbs the fast evolving polarization, and the resultant absorbance change is monitored in dilute helium, dense helium, and sulfur hexafluoride (SF6) molecules. We observe and quantify the time-dependence of various transient phenomena in helium atoms,includinglaser-inducedphase(LIP),time-varying(AC)Starkshift,quantumpathinterference, and laser-induced continuum structure. In the case of dense helium targets, we discuss nonlinear macroscopic propagation effects pertaining to LIP and resonant pulse propagation, which accoun tfor the appearance of new spectral features in transient lineshapes. We then use tunable NIR photons to demonstrate the wavelength dependence of the transient laser induced effects. In the case of molecular polarization experiment in SF6, we show suppression of XUV photoabsorption corresponding to inter-valence transitions in the presence of a strong NIR field. In each case, the temporal evolution of transient absorption spectra allows us to observe and understand the transient laser induced modifications of the electronic structure of atoms and molecules. Full article

The design of grating-based instruments to handle and condition coherent ultrafast pulses in the extreme-ultraviolet is discussed. The main application of such instruments is the monochromatization of high-order laser harmonics and free-electron-laser pulses in the femtosecond time scale. Broad-band monochromators require the use of diffraction gratings at grazing incidence. A grating can be used for the spectral selection of ultrashort pulses without altering the pulse duration in a significant way, provided that the number of illuminated grooves is equal to the resolution. We discuss here the design conditions to be fulfilled by a grating monochromator that does not increase the pulse duration significantly longer than the Fourier limit. Full article

The optical klystron enhancement to a self-amplified spontaneous emission free electron laser has been studied in theory and in simulations and has been experimentally demonstrated on a single-pass high-gain free electron laser, the FERMI FEL-1, in 2014. The main concept consists of two undulators separated by a dispersive section that converts the energy modulation induced in the first undulator in density modulation, enhancing the coherent harmonic generation in the first part of the second undulator. This scheme could be replicated in a multi-stage: the bunching is enhanced after each dispersive section, consistently reducing the saturation length. We have applied the multi-stage optical klystron (OK) scheme on the FEL-2 line at FERMI, whose layout includes three dispersive sections. Optimizing the strength of the dispersions allowed a significant increase of the self-amplified spontaneous emission (SASE) intensity in comparison to a single-stage OK and extending to the soft-X rays the OK enhanced SASE previously demonstrated on FEL-1. Full article

Optical transmission technologies optimized for optical network segments sensitive to power consumption and cost, comprise modulation formats with direct detection technologies. Specifically, non-return to zero differential quaternary phase shift keying (NRZ-DQPSK) in deployed fiber plants, combined with high-performance, low-complexity electronic equalizers to compensate residual impairments at the receiver end, can be proved as a viable solution for high-performance, high-capacity optical links. Joint processing of the constructive and the destructive signals at the single-ended DQPSK receiver provides improved performance compared to the balanced configuration, however, at the expense of higher hardware requirements, a fact that may not be neglected especially in the case of high-speed optical links. To overcome this bottleneck, the use of partially joint constructive/destructive DQPSK equalization is investigated in this paper. Symbol-by-symbol equalization is performed by means of Volterra decision feedback-type equalizers, driven by a reduced subset of signals selected from the constructive and the destructive ports of the optical detectors. The proposed approach offers a low-complexity alternative for electronic equalization, without sacrificing much of the performance compared to the fully-deployed counterpart. The efficiency of the proposed equalizers is demonstrated by means of computer simulation in a typical optical transmission scenario. Full article

Space division multiplexing (SDM) is a promising technology that aims to overcome the capacity crunch of optical communications. In this paper, we introduce the multiple-input multiple-output (MIMO) Stokes Space Algorithm (SSA) implemented in frequency domain, a novel equalization technique for space division multiplexing (SDM). Although different papers have been published about the SSA and its MIMO implementation, we provide for the first time an analysis of the of the convergence speed and frequency offset of the SSA compared to the least mean square (LMS). SSA algorithm can deal with higher frequency offsets and linewidths than LMS, being suitable for optical communications with higher phase noise. SSA does not need pre-compensation of frequency offset, which can be compensated after equalization without penalties. On the other hand, due to reduced convergence speed, SSA requires longer training sequences than LMS. Full article

Nonlinear diffuse femtosecond-pulse reflectometry is introduced as a powerful experimental tool for the unambiguous characterization of polar and non-polar point symmetry groups of harmonic upconversion nanoparticles. Using intense ultrashort 40 femtosecond laser pulses and an appropriate figure of merit (FOM), second and third harmonic emission serve for the structural characterization of polar Yb-doped lithium niobate and non-polar titanium dioxide nanoparticles. The tool is capable of differentiating these two samples by FOM values that differ by up to 13 orders of magnitude. The general applicability to harmonic upconversion nanoparticles over a broad range of intensities and wavelength spectrum, is discussed. Full article

For distances less 10 nm, a total energy transfer occurs from a quantum emitter to a nearby metallic surface, producing evanescent surface waves that are plasmonic in nature. When investigating a metallic nanohole supported on an optically dense substrate (such as diamond with nitrogen vacancy center), the scattering occurred preferentially from the diamond substrate towards the air for dipole distances less 10 nm from the aperture. In addition, an enhancement to the dipole’s radiative decay rate was observed when resonance of the aperture matched the emitters wavelength. The relationship between an emitter and a nearby resonant aperture is shown to be that of the resonance energy transfer where the emitter acts as a donor and the hole as an acceptor. In conjunction with the preferential scattering behavior, this has led to the proposed device that operates in transmission mode, eliminating the need for epi-illumination techniques and optically denser than air superstrates in the collection cycle, hence making the design simpler and more suitable for miniaturization. A design criterion for the surface grating is also proposed to improve the performance, where the period of the grating differs significantly from the wavelength of the surface plasmon polaritons. Response of the proposed device is further studied with respect to changes in nitrogen vacancy’s position and its dipolar orientation to identify the crystallographic planes of diamond over which the performance of the device is maximized. Full article

We experimentally investigate the transmission performance of 56 Gb/s four-level pulse amplitude modulation (PAM-4) over 30-km standard single mode fiber (SMF) using a C-band EML for low-cost metro and short-reach wavelength division multiplexing (WDM) applications. Bit error rate (BER) performance below the HD-FEC threshold is achieved for up to 30-km maximum reported distance without employing dispersion compensation fiber (DCF) in the link. Full article

The current demand for fabricating optical and photonic devices displaying high performance, using low-cost and time-saving methods, prompts femtosecond (fs)-laser processing as a promising methodology. High and low repetition femtosecond lasers enable surface and/or bulk modification of distinct materials, which can be used for applications ranging from optical waveguides to superhydrophobic surfaces. Herein, some fundamental aspects of fs-laser processing of materials, as well as the basics of their most common experimental apparatuses, are introduced. A survey of results on polymer fs-laser processing, resulting in 3D waveguides, electroluminescent structures and active hybrid-microstructures for luminescence or biological microenvironments is presented. Similarly, results of fs-laser processing on glasses, gold and silicon to produce waveguides containing metallic nanoparticles, analytical chemical sensors and surface with modified features, respectively, are also described. The complexity of fs-laser micromachining involves precise control of material properties, pushing ultrafast laser processing as an advanced technique for micro/nano devices. Full article

The nonlinear interaction between Near-Infrared (NIR) and Terahertz pulses is principally investigated as a means for the detection of radiation in the hardly accessible THz spectral region. Most studies have targeted second-order nonlinear processes, given their higher efficiencies, and only a limited number have addressed third-order nonlinear interactions, mainly investigating four-wave mixing in air for broadband THz detection. We have studied the nonlinear interaction between THz and NIR pulses in solid-state media (specifically diamond), and we show how the former can be frequency-shifted up to UV frequencies by the scattering from the nonlinear polarisation induced by the latter. Such UV emission differs from the well-known electric field-induced second harmonic (EFISH) one, as it is generated via a phase-insensitive scattering, rather than a sum- or difference-frequency four-wave-mixing process. Full article