masteruan

Hi,try to find your answer here: http://community.mydevices.com/t/wecome-to-the-mydevices-cayenne-community-forum/20

When I try the code...Segmentation faultSegmentation faultSegmentation faultSegmentation fault

Raspberry Pi is simply to run Glediator.

I see the screen only after reset Arduino UNO...

Hi,try this: http://kig.re/2014/12/31/how-to-use-arduino-nano-mini-pro-with-CH340G-on-mac-osx-yosemite.html

Reinstall the USB driver for serial converter.Try to read this: http://kig.re/2014/12/31/how-to-use-arduino-nano-m...

Download CoolTerm:http://freeware.the-meiers.orgConnect the laser engraver, and open the program. See the port.

I think that is a problem of value of stepper motors. Control the voltage of driver, control the values of stepper motor, use another program for verify if is a software problem.Post your trouble on this forum: http://www.shapeoko.com/forum/viewforum.php?f=3

Depend from driver see this:https://www.youtube.com/watch?v=GM6T-GwXqPQ

Have you another Arduino UNO? Can you try the GRBL shield with another Arduino UNO

See this: https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.9

Great idea! You can use Processing for example...

Try to change the Arduino board with an Arduino official.

I think that is a permissions problem

Hi dear,try to read this: https://bbs.nextthing.co/t/solved-special-permissions/1797

[FIXED Z axis problem]I've fixed this problem. It's a problem with Arduino shield and mac OS Sierra drivers. Now I'm replaced the Chinese Arduino board with a new Arduino board, and all work.

Great Project!I've a problem with Z axis. I've Arduino and CNC Shield like in your Instructables. When I try to move the Z axis this remain stop, and the others motors make a noise. The others motors work properly, and also the switch for relay.1. If I put the motor Z on the driver X or Y is OK. Move2. If I put the DRV8825 driver Z on CNC Shield pin X or T axis it's OK.3. If I put the X or Y motor in Z driver on CNC shield not work.a. Wich kind of cnc shield do you have? b. Can I test the CNC shield?Thank's

Dear,this is for library: https://www.arduino.cc/en/Guide/Libraries

Yes is SDA

Dear,I've correct the error. Now you can download the file.

It's the final code.The GSR is a value of skin conductance. When a person tells lies, in many cases, he have an increase of arousal. One of the reactions of arousal is the sweat, and an increase of sweat is equal an increase of GSR.

What python version are you using? python3 doesnt install it's gpio package through that, so it's only installed in python 2.x

Great! Follow the Instructable :-)

Thank's :-)

The 4 resistors are for leds. The resistor for probe is 1 M ohm.

I don't know...

I don't know

Hello,try this:http://s000.tinyupload.com/index.php?file_id=77329189466431957967

Ohhhhh right!!

Thanks for read my project.

Hi dear,You can buy the tmp sensor here: http://amzn.to/2cdthYmAnd the breadboard here: http://amzn.to/2cxeMxU

Wooo great! Post some photo if you can.Thank's for your message. I make the Instructables just for people like you :)

Woooo great!

Sorry it took a little while, I contacted Cayenne directly and asked them and it took them some time to answer. While you are correct that it’s possible to set up scheduled events within Cayenne, there’s not currently a way of setting a piece of timer-enabled hardware to trigger an action. But the developers are always looking for feature ideas, so if you let them know in the forum, they can try to add that feature! http://community.mydevices.com/