Technologies — Open Access Journal

The aims of this study were to determine the proximate composition of cacao pod husk as well as the optimal conditions for extraction and purification of theobromine from cacao pod husk. The results indicated that cacao pod husk had high contents of moisture and carbohydrate (87.06% and 11.03% by fresh weight, respectively), but low contents of crude protein, crude lipid, and ash (0.31%, 0.12%, and 1.48% by fresh weight, respectively). The optimal conditions for extraction of theobromine from cacao pod husk were of 70% ethanol, with an extraction time of 90 min, and 1 as the number of extractions. A concentration of 10% by volume of 10% lead acetate solution was the best selection for purification of the crude extracts containing theobromine from cacao pod husk. Under these optimal conditions, theobromine content obtained from cacao pod husk was 6.79 mg/100 g dry weight. The finding from this study is a valuable contribution for obtaining theobromine from an abundant, inexpensive, renewable, and sustainable source for potential application in the nutraceutical, medical, and pharmaceutical industries. Full article

Moveable factories can enable leapfrogging of fixed industrial factories, and so make immediate contributions to global goals of more resilient sustainable manufacturing. Moveable factories bring into use diverse technological advances that reduce the number, size, and weight of machines needed to carry out manufacturing operations at points of supply and/or demand. However, fixed industrial factories continue to be the principal focus for development and application of new manufacturing technologies. At the same time, fixed industrial factories continue to be seen by policy makers around the world as the default option for developing prosperity: rather than as an old fashioned production paradigm to be leapfrogged over. In this paper, findings are reported from a case study investigating potential for moveable factories to bring leapfrog manufacturing to an industrial economy. This case study comprised literature review, interviews, and theoretical analyses. Study findings indicate that organisations in an industrial economy will consider moveable factories if fixed factories are not feasible, practical, or viable. By contrast, potential for improved efficiency and flexibility may not be sufficient to motivate a shift away from fixed industrial factories. Full article

An effective Supervisory Control and Data Acquisition (SCADA) system can improve the reliability, safety and economic benefits of a microgrid operation. In this research, the lower central controller and upper WEB (World Wide Web) monitoring system are connected by the SCADA system, which is the hub of a microgrid intelligent monitoring platform. This system contains a set of specific functions programmed by Java as a middleware and can provide communication and control functions between the central controller and the upper monitoring system. For the sake of security and stability of the microgrid, the SCADA system realizes business processing on real-time data acquisition and storage, load balancing and resource recovery, concurrent security processing, and control instruction parsing and transmission. All those functions were tested and verified in actual operation. Full article

Laying ballastless track on railway bridges has the advantages of reducing the train noise problem, improving passenger comfort, and reducing track maintenance costs. Therefore, railway bridges with ballastless track have gradually turned into a major trend in railway systems all over the world. In Taiwan, railway bridges with ballastless track have been in use for many years, with ballastless track turnouts also starting to be constructed in recent years. Where railway bridges with ballastless track turnouts are located in urban areas, special consideration must be given to the road crossings and the use of continuous bridges in the turnout zones. Accordingly, there arise a number of difficulties related to the bridge configurations or the continuous length of bridges being excessively long. Often, such situations necessitate the use of extremely large-sized bridge piers in the bridge design, or create the risk of serious damage to the pier structure should insufficient attention be given to any of the factors. This article will take a continuous prestressed concrete bridge as an example. The prestressed concrete bridge must be absolutely continuous, be able to include ballastless track turnout zones, and meet the needs of crossing roads. For this example, the length of the continuous prestressed concrete bridge is over 300 m. This article will also discuss the configuration of a continuous prestressed concrete bridge of railway, and—through the analysis of track–bridge interaction and temperature detection—provides suggestions on the optimal configuration model of the continuous prestressed concrete bridges, which should allow improper configuration and possible structural damage to be avoided. Full article

This paper deals with decision fusion in wireless sensor networks (WSNs) over Rayleigh fading channels. The likelihood ratio test (LRT) is considered as the optimal fusion rule when applied at the fusion center (FC). However, applying the LRT at the FC requires both the channel state information (CSI) and the local sensors’ performance indices. Acquiring such information is considered as an overhead in energy and bandwidth constrained systems such as WSNs. To avoid these drawbacks, we propose a modification to the traditional three-layer system model of a WSN where the LRT is applied as a local decision making method at the sensors level. Applying the LRT at the sensors level does not require the CSI or the local sensors’ performance indices. It only requires the signal-to-noise ratio (SNR). Moreover, a new fusion rule based on selection combining (SC) is suggested. This fusion method has the lowest complexity when compared to other diversity combining based fusion rules such as the equal gain combiner (EGC) and the maximum ratio combiner (MRC). Simulation results show that the performance of the proposed model outperforms the traditional model. In addition, applying the EGC at the FC in the proposed model provides comparable performance to the traditional model that applies the LRT at the FC. Full article

The layer-by-layer building methodology used within the powder bed process of Selective Laser Melting facilitates control over the degree of melting achieved at every layer. This control can be used to manipulate levels of porosity within each layer, effecting resultant mechanical properties. If specifically controlled, it has the potential to enable customisation of mechanical properties or design of in-built locations of mechanical fracture through strategic void placement across a component, enabling accurate location specific predictions of mechanical failure for fail-safe applications. This investigation examined the process parameter effects on porosity formation and mechanical properties of 316L samples whilst maintaining a constant laser energy density without manipulation of sample geometry. In order to understand the effects of customisation on mechanical properties, samples were manufactured with in-built porosity of up to 3% spanning across ~1.7% of a samples’ cross-section using a specially developed set of “hybrid” processing parameters. Through strategic placement of porous sections within samples, exact fracture location could be predicted. When mechanically loaded, these customised samples exhibited only ~2% reduction in yield strength compared to samples processed using single set parameters. As expected, microscopic analysis revealed that mechanical performance was closely tied to porosity variations in samples, with little or no variation in microstructure observed through parameter variation. The results indicate that there is potential to use SLM for customising mechanical performance over the cross-section of a component. Full article

The present study deals with the properties of five different metals/alloys (Al-12Si, Cu-10Sn and 316L—face centered cubic structure, CoCrMo and commercially pure Ti (CP-Ti)—hexagonal closed packed structure) fabricated by selective laser melting. The room temperature tensile properties of Al-12Si samples show good consistency in results within the experimental errors. Similar reproducible results were observed for sliding wear and corrosion experiments. The other metal/alloy systems also show repeatable tensile properties, with the tensile curves overlapping until the yield point. The curves may then follow the same path or show a marginal deviation (~10 MPa) until they reach the ultimate tensile strength and a negligible difference in ductility levels (of ~0.3%) is observed between the samples. The results show that selective laser melting is a reliable fabrication method to produce metallic materials with consistent and reproducible properties. Full article

Through reduced 3-D printer cost, increased usability, and greater material selection, additive manufacturing has transitioned from business manufacturing to the average prosumer. This study serves as a representative model for the potential future of 3-D printing in the average American household by employing a printer operator who was relatively unfamiliar with 3-D printing and the 3-D design files of common items normally purchased by the average consumer. Twenty-six items were printed in thermoplastic and a cost analysis was performed through comparison to comparable, commercially available products at a low and high price range. When compared to the low-cost items, investment in a 3-D printer represented a return of investment of over 100% in five years. The simple payback time for the high-cost comparison was less than 6 months, and produced a 986% return. Thus, fully-assembled commercial open source 3-D printers can be highly profitable investments for American consumers. Finally, as a preliminary gauge of the effect that widespread prosumer use of 3-D printing might have on the economy, savings were calculated based on the items’ download rates from open repositories. Results indicate that printing these selected items have already saved prosumers over $4 million by substituting for purchases. Full article

A wireless accelerometer has been used in conjunction with a dedicated 3T neonatal MRI system installed on a Neonatal Intensive Care Unit to measure in-plane rotation which is a common problem with neonatal MRI. Rotational data has been acquired in real-time from phantoms simultaneously with MR images which shows that the wireless accelerometer can be used in close proximity to the MR system. No artifacts were observed on the MR images from the accelerometer or from the MR system on the accelerometer output. Initial attempts to correct the raw data using the measured rotational angles have been performed, but further work will be required to make a robust correction algorithm. Full article

This study examines the role of Graphene nanoplatelets (GNPs) as a solid lubricant additive to aluminum. Pure Al and Al-2 vol % GNP pellets are sintered by Spark Plasma Sintering (SPS). Their tribological properties are evaluated by a ball-on-disk tribometer at room temperature (RT) and high temperature (200 °C). Al-2 vol % GNP composite displayed poor densification (91%) and low hardness, resulting in poor wear resistance as compared to pure Al. However GNP addition resulted in a lower coefficient of friction (COF) as compared to pure aluminum at both temperatures. The results demonstrated that GNPs contribute to reducing COF by forming a protective tribolayer. GNPs also play a unique role in reducing oxygen ingress at 200 °C. It is concluded that the packing density of a starting powder blend of Al-GNP needs to be improved by using irregular shaped aluminum powder mixed with both larger and smaller GNPs. This would result in greater densification and improve wear rate while maintaining low COF. Full article

The current paper aims to review tooling life span, failure modes and models in cold microforming processes. As there is nearly no information available on tool-life for microforming the starting point was conventional cold forming. In cold forming common failures are (1) over stressing of the tool; (2) abrasive wear; (3) galling or adhesive wear, and (4) fatigue failure. The large variation in tool life observed in production and how to predict this was reviewed as this is important to the viability of microforming based on that the tooling cost takes a higher portion of the part cost. Anisotropic properties of the tool materials affect tool life span and depend on both the as-received and in-service conditions. It was concluded that preconditioning of the tool surface, and coating are important to control wear and fatigue. Properly managed, the detrimental effects from surface particles can be reduced. Under high stress low-cycle fatigue conditions, fatigue failure form internal microstructures and inclusions are common. To improve abrasive wear resistance larger carbides are commonly the solution which will have a negative impact on tooling life as these tend to be the root cause of fatigue failures. This has significant impact on cold microforming. Full article

The present study shows the process followed in making the three-dimensional model and geometric documentation of a historical invention of the renowned Spanish engineer Agustin de Betancourt y Molina, which forms part of his rich legacy. Specifically, this was a wind machine for draining marshy ground, designed in 1789. The present research relies on the computer-aided design (CAD) techniques using Autodesk Inventor Professional software, based on the scant information provided by the only two drawings of the machine, making it necessary to propose a number of dimensional and geometric hypotheses as well as a series of movement restrictions (degrees of freedom), to arrive at a consistent design. The results offer a functional design for this historic invention. Full article

We review our unified optimized approach to the dynamical control of quantum-probe interactions with noisy and complex systems viewed as thermal baths. We show that this control, in conjunction with tools of quantum estimation theory, may be used for inferring the spectral and spatial characteristics of such baths with high precision. This approach constitutes a new avenue in quantum sensing, dubbed quantum noise spectroscopy. Full article

In 2002, the European Commission (EU) issued a Directive aiming to reduce the energy consumption of buildings, which was adopted by the EU member states and came into force in 2006. Portugal adopted it by issuing law decrees in 2006 which considered not only the energy saving aspects but also additional specific measures aiming to protect indoor air quality (IAQ). This new legislation is now being enforced, and it will be necessary to define compliance acceptance levels for the prescribed indoor air limits. The use of comfort or environmental indexes could be of considerable help to ameliorate the evaluation of IAQ. This paper presents a proposal of an index regarding IAQ which considers both the aspects of thermal comfort and non-toxicity. The proposed index was calculated for offices of several European countries, available from previous studies and for Portugal as well. Bearing in mind there is few existing data, this study is consistent with the proposed index, as the obtained values are similar to Greece, which has several similarities with the Portuguese situation. Full article

Since its first experimental demonstration, ghost imaging has attracted a great deal of attention due to interests in its fundamental nature and its potential applications. In terms of applications, the most interesting and useful feature, perhaps, is the turbulence insensitivity of thermal light ghost imaging, i.e., atmospheric turbulence would not have any influence on the ghost images of sunlight. Inspired by ghost imaging, a new type of camera is ready for turbulence-free imaging applications. This turbulence-free camera would be especially useful for long distance imaging, such as satellite imaging. How could fluctuations of thermal light produce an image? Why is it turbulence-free? This article addresses these questions. Full article

Additive manufacturing processes such as selective laser melting (SLM) are attracting increasing attention and are regarded as the manufacturing technology of the future, because of their ability to produce near net shaped components of theoretically any shape with added functionality. Various properties, including mechanical, tribological, welding, and corrosion properties, of Al-12Si alloys fabricated via SLM have been extensively studied. However, all of these studies were carried out at ambient conditions. Nevertheless, under working conditions, these alloys experience service temperatures ranging between 373 and 473 K. The present study focuses on the evaluation of the mechanical properties of SLM-fabricated Al-12Si alloys in this temperature range. For this, Al-12Si alloy specimens were annealed at 573 K, a temperature well beyond the test temperature in order to provide a stable microstructure during tensile testing. The plasticity of these materials increases along with the size of the dimples on the fracture surface with increasing tensile test temperature. Moreover, the annealed Al-12Si alloy exhibits appreciable tensile properties when tested between 373 K and 473 K. The results suggest that Al-12Si samples fabricated via SLM may be ideal candidates for automotive applications such as pistons and cylinder heads. Full article

The effect of Mg-7.4%Al reinforcement particle size on the microstructure and mechanical properties in pure Al matrix composites was investigated. The samples were prepared by hot consolidation using 10 vol.% reinforcement in different size ranges, D, 0 < D < 20 µm (0–20 µm), 20 ≤ D < 40 µm (20–40 µm), 40 ≤ D < 80 µm (40–80 µm) and 80 ≤ D < 100 µm (80–100 µm). The result reveals that particle size has a strong influence on the yield strength, ultimate tensile strength and percentage elongation. As the particle size decreases from 80 ≤ D < 100 µm to 0 < D < 20 µm, both tensile strength and ductility increases from 195 MPa to 295 MPa and 3% to 4% respectively, due to the reduced ligament size and particle fracturing. Wear test results also corroborate the size effect, where accelerated wear is observed in the composite samples reinforced with coarse particles. Full article

The aim of this study was to determine the mass proportion of carrot root and the effects of four various solvents (methanol, water, ethanol and hexane) on the contents of total phenolics and saponins as well as antioxidant capacity of carrot peel to identify an optimal solvent for effective extraction of bioactive compounds from carrot peel for further investigation. The results showed that carrot root consisted of body, heads and peel with their mass proportion of 83.19%, 5.01% and 14.19% by fresh weight, respectively. Among four solvents tested, methanol obtained the highest levels of extraction yield (54.02% by dry weight), total phenolic content (9.02 mg GAE/g dry weight) and antioxidant capacity (DPPH radical scavenging capacity, cupric ion reducing antioxidant capacity, and ferric reducing antioxidant power) from carrot peel, while water extracted the highest content of saponins (272.9 mg EE/g dry weight) and possessed the maximum ABTS radical scavenging capacity. Therefore, methanol and water are considered for effective extraction of phenolics and saponins from carrot peel, respectively. The phenolic/saponin-enriched extracts are potential sources for further applications in the healthy food and/or pharmaceutical industries. Full article

(1) Background: Recent reforms in Australia, providing people with disability and older people with choice and control over allocated funding, have altered consumer expectations and transformed the landscape of assistive technology (AT) service provision. The purpose of this study is to report on the routine AT outcomes of people who accessed an AT consultation service and examine how well these capture the impact of AT on their lives; (2) Methods: This study, which uses mixed methods for concurrent triangulation of the data, reports on the outcomes for 127 people who acquired a range of assistive technology in 2015 and examines the adequacy of an existing service outcome framework in capturing the true value of these technologies to AT users. Outcome data was routinely collected by a community service 2–4 months following an AT consultation. A telephone or face-to-face interview gathered demographic information as well as AT outcomes, using two standardized tools, the Individualized Prioritised Problem Assessment (IPPA) and the EATS 6D. Qualitative comments relating to the impact of the AT on the person’s life were also documented; (3) Results: The acquired AT generally met or exceeded expectations of the person using the AT and the attending health professional. Overall, people experienced decreased difficulty and increased feelings of autonomy, with most of the reported improvements identified in mobility and usual activities; (4) Conclusion: Routine outcome data provide some evidence of the value of AT in addressing concerns as identified by clients. Qualitative data, which captured the impact of AT on people’s lives, suggest that the empowering and transformative aspects of AT are not currently being captured by existing measures. Full article