This section describes a process for configuring and starting GTID-based replication in MySQL 5.6. This is a “cold start” procedure that assumes either that you are starting the replication master for the first time, or that it is possible to stop it; for information about provisioning replication slaves using GTIDs from a running master, see Section 17.1.3.3, “Using GTIDs for Failover and Scaleout”.

The key steps in this startup process for the simplest possible GTID replication topology—consisting of one master and one slave—are as follows:

In the following example, two servers are already running as master and slave, using MySQL's “classic” file-based replication protocol.

Most of the steps that follow require the use of the MySQL root account or another MySQL user account that has the SUPER privilege. mysqladmin shutdown requires either the SUPER privilege or the SHUTDOWN privilege.

Step 1: Synchronize the servers.  Make the servers read-only. To do this, enable the read_only system variable by executing the following statement on both servers:

mysql> SET @@global.read_only = ON;

Then, allow the slave to catch up with the master. It is extremely important that you make sure the slave has processed all updates before continuing.

Step 2: Stop both servers.  Stop each server using mysqladmin as shown here, where username is the user name for a MySQL user having sufficient privileges to shut down the server:

shell> mysqladmin -uusername -p shutdown

Then supply this user's password at the prompt.

Step 3: Restart both servers with GTIDs enabled.  To enable binary logging with global transaction identifiers, each server must be started with GTID mode, binary logging, slave update logging enabled, and with statements that are unsafe for GTID-based replication disabled. In addition, you should prevent unwanted or accidental updates from being performed on either server by starting both in read-only mode. This means that both servers must be started with (at least) the options shown in the following invocation of mysqld_safe:

shell> mysqld_safe --gtid_mode=ON --log-bin --log-slave-updates --enforce-gtid-consistency &

In addition, you should start the slave with the --skip-slave-start option along with the other server options specified in the example just shown.

For more information about the --gtid-mode and --enforce-gtid-consistency server options, see Section 17.1.4.5, “Global Transaction ID Options and Variables”.

Depending on your configuration, supply additional options to mysqld_safe or other mysqld startup script.

Step 4: Direct the slave to use the master.  Tell the slave to use the master as the replication data source, and to use GTID-based auto-positioning rather than file-based positioning. Execute a CHANGE MASTER TO statement on the slave, using the MASTER_AUTO_POSITION option to tell the slave that transactions will be identified by GTIDs.

You may also need to supply appropriate values for the master's host name and port number as well as the user name and password for a replication user account which can be used by the slave to connect to the master; if these have already been set prior to Step 1 and no further changes need to be made, the corresponding options can safely be omitted from the statement shown here.

mysql> CHANGE MASTER TO
     >     MASTER_HOST = host,
     >     MASTER_PORT = port,
     >     MASTER_USER = user,
     >     MASTER_PASSWORD = password,
     >     MASTER_AUTO_POSITION = 1;

Neither the MASTER_LOG_FILE option nor the MASTER_LOG_POS option may be used with MASTER_AUTO_POSITION set equal to 1. Attempting to do so causes the CHANGE MASTER TO statement to fail with an error.

Assuming that the CHANGE MASTER TO statement has succeeded, you can then start the slave, like this:

mysql> START SLAVE;

Step 5: Disable read-only mode.  Allow the master to begin accepting updates once again by running the following statement:

mysql> SET @@global.read_only = OFF;

GTID-based replication should now be running, and you can begin (or resume) activity on the master as before. Section 17.1.3.3, “Using GTIDs for Failover and Scaleout”, discusses creation of new slaves when using GTIDs.