MertArduino

Congratulations. I wish you continued projects.

I actually said these values because of the sensitivity of the sensor. Normally, as seen on the video, the minimum value be down to 1009. I agree with you, this value can be increased with materials you say.

Thanks for your nice comment ;)

http://mertarduinotutorial.blogspot.com.tr/2016/12/arduino-project-tutorial-12-line.html

Fantastic! I liked it. Good idea. :)

Thanks for comment ;)

It is empty. Red wire is not connect any where.

Please watch this tutorial; https://youtu.be/Es8D1q_b-c4

You can copy from here: http://mertarduinotutorial.blogspot.com.tr/2016/12/arduino-project-tutorial-01-obstacle.html

You can copy from here; http://mertarduinotutorial.blogspot.com.tr/2016/12/arduino-project-tutorial-01-obstacle.html

I will try to help;- If the motors are moving with USB, please check your external power connections for L293D.- It may be a simple suggestion, but it has happened before, so renew your external battery. (That means the battery you are using does not have enough power.)- I need to see your robot in order to produce a solution. If possible, upload the images of the robot here.

Sorry. I don't understand you :/ What are you talking about?

Thank you for your message. Could you give me some more details about the project?

Congratulations. I hope it helps ;)

Congratulations for your work. But I helped my followers. Just like I helped you. ;)This comment has been a bit disrespectful. :/ I think you should open an instructables account, you can share your work from your own account.

Hi vincent44,Where are u from? Because I don't understand sorry :/ What did you mean "keskin yakınlık sensörü"?

I don't fully understand the problem. But you can add arm. And you can get the power from one place. You need to use a good battery (maybe li-on). And distribute by calculating the power with the help of a breadboard.

Paylaşımlardan ziyade paylaştığın projeler eğer özellikli ise, yani onların deyimiyle 'featured' ise premium üyelik hakkı tanıyorlar. Ben sana özelden bir premium hediyesi göndereceğim. O kodu kullanırsan bazı site özelliklerinden de yararlanabilirsin. Eğitim ve kurslar v.b.

Mesaj gönderirken fark ettim, sanırım senin premium aboneliğin mevcut :)

Mesaj gönderirken fark ettim, sanırım sende premiumsun. ;)

Yorumların ve desteğin için teşekkür ederim. Ön tarafta kullanmış olduğum tekerlek 'sarhoş tekerlek' olarak satılmakta. Çok çeşidi var. İnternet üzerinden çeşitleri inceleyebilirsin.

You sent 5 different codes. They all made an error! Where's my code? And why are there 5 codes? Download my code again! Do what I told you before and upload it! Do not forget to install NewPing and AFMotor.h libraries. And do not run my code directly! Just copy it. Then open a new page in Arduino and paste it. Connect the robot, choose which port you have connected and upload it!

Connections seem right. Is there any problem?

Only the rotation of the wheels may not be equal. If this is the case, it is enough to replace the DC motor connections in the motor shield.

It could be a really good project.But the project algorithm can be very difficult.You can use the DS3231 RTC. I would very much like to help but it takes a long time and I do not have much time.I think, first of all, the power output of all the lights should be from one place. So it must be intertwined with an Arduino scheme. Otherwise, the project needs to be extended and remotely controlled. Different modules are used in this. If all the light inputs are in one place, the DC3231 RTC and Arduino are programmed. Then you can interact with the lights using the relay card. A project that should be considered long and carefully!

If you installed libraries, you can try. If you get any errors write me again.

If there is a continuation of the error code, send it as well. If it's just that; Copy the whole code and close the IDE window. Then open the Arduino IDE again. Open a new window. Delete the contents. And paste the code. Make sure the COM entry is correct. (For example COM5 - COM8 and so on). Finally, upload the code. Use Windows 10? Did you download the Arduino program from the Windows market or is the arduino from its official website?

I'm warning you! bare wires should not be touch each other! You need to work more carefully. It can damage the Arduino.When you solve the problem would be correct connections.

Congratulations. I like it ;)

It's a great idea, but not helpful. Now, you must cut off the end of the wire. So you should cut the cable headers you want to attach to the motor drive. Then peel off the end of a small amount of wires. Connect in this way the cables to motor drive.Be sure to watch the video carefully.like these

Takibin ve yorumların için ben teşekkür ederim.

I was very happy for your comment. Congratulations and thank you.

Yorumun için bende sana teşekkür ederim. Ama "Hocam" sıfatını hak edecek bir şey yaptığımı düşünmüyorum. Ben sadece hobi olarak ilgileniyorum. Gerçek emekçilere haksızlık olmasın ;) Geçen gün sana bir adres yolladım, arduino başlangıcı ile ilgili. Hemen hemen tüm konulara oradan ulaşabilirsin bilgine.

https://gelecegiyazanlar.turkcell.com.tr/konu/ardu...Paylaştığım platformdan arduino için temel kodlara giriş yapabilirsin. Gayet açık ve basit bir dil ile anlatılmış.